The Astek A-LSI9300-8e has unique firmware and is tested and certified with the Astek A54812-SW SAS switch.

The Astek A-LSI9300-8e has unique firmware and is tested and certified with the Astek A54812-SW SAS switch.

12Gb/s. 8-Port External, Gen3 SAS, Gen3 PCI Host Bus Adapter

The Astek A-LSI9300-8e has unique firmware and is tested and certified with the Astek A54812-SW SAS switch.

CompactFlash for Embedded Systems

 A complete, pre-programmed, Gen2 6Gbps SAS Expander in a PCI/PCI-Express card form factor. For designers looking to add SAS fanout to a design, the Astek A33606-PCI card jump-starts the design cycle by delivering a complete SAS expander subsystem.

The A33606-PCI-60-6A is a 36-port 6Gb/s SAS/SATA expander in a PCIe form factor. The A33606-PCI-60-6A comes pre-configured with a sanitization algorithm that will sanitize up to 16 Self-Encrypting Drives (SED) that support the Cryptographic Erase Functions “Key Erase” (SBC-3, Sections 5.24/2/4) and “Block Erase” (SBC-3, Section 5.24.2.3).

12Gb/s SAS, high port count expander card doubles the SAS data rate from
previous generations providing high performance and large scalability

  The A34812-ITX is a 48-lanes 12Gb/s SAS/SATA expander in a mini-ITX form factor. 

 The Astek A3803-PMC doubles the performance of dual channel Ultra320 SCSI HBAs with 
aggregate I/O port bandwidth of 2.4GBytes/s and full duplex capability.  

The Astek A3803-PMC-55 brings SAS functionality to SPARC Compact PCI (cPCI) and VME blades, allowing legacy SPARC and 5V-only (non PCI-X) blades to use modern SAS and SATA disk media. To simplify system builder's inventory control, the A3803-PMC-55 can operate in both 5V only environments (at PCI-66/64), and full rate 133Mhz/64-bit in PCI-X environments

MMU - Military Grade MMU with 6 Bays, Crypto and push button erase function.

12G Test JBOD with four x4  External SFF-8644 External Ports and sixteen  12G SAS Dual Ported drive bays (2.5" drives).  Drive bays also support 6G SATA. 

  The Astek A54812 is a 1U high, 12-port (48-lanes) 12Gb/s SAS switch configured with 12 x4 wide-port each capable of 48Gb/s . The switch extends the capabilities of SAS in direct-attached storage (DAS) environments by allowing multiple servers to connect to one or more independent storage systems.

  The Astek A54812 is a 1U high, 12-port (48-lanes) 12Gb/s SAS switch configured with 12 x4 wide-port each capable of 48Gb/s . The switch extends the capabilities of SAS in direct-attached storage (DAS) environments by allowing multiple servers to connect to one or more independent storage systems.

 Astek offers a 1, 2 &3 meter version of the HD mini-SAS (SFF8644) to HD mini-SAS (SFF8644) SAS cables

Mid-bus probing for gen2 PCIe lanes

•  Supports Gen 1 and Gen 2 PCI Express probing.
•  x1 to x16 unidirectional
•  x1 to x8 bidirectional
•  27” full cable length.
•  12.5” length on low-profile portion
•  0.68” Mated height
•  1 year limited warranty

PCIe gen3 Mid-bus Probe

• Supports Gen 1, Gen 2, and Gen 3 PCI Express probing.
•  x1 to x16 unidirectional
•  x1 to x8 bidirectional
•  27” full cable length.
•  12.5” length on low-profile portion
•  0.68” Mated height
•  1 year limited warranty

The Astek A43212-SAN  drive sanitizer provides fast secure block level sanitization for data centers.  The Astek sanitizer enables loose drives or drives mounted in almost any carrier to connect directly to the system. Drives are safely stored in one of four trays capable of supporting up to 8 hard drives each with speeds up to 1GBs per drive. 

The DDR5 Controller Board provides DRAM testing signals. Utilizing the RCD's Virtual Host Mode (VHOST).

DDR5 CTC2 test fixture provides a method of compliance testing of DDR5 components and RDIMM cards.

DDR5 Parametric Test Fixtures enable probing and characterization of DDR5 signals on a DIMM connector

DDR5 SMP replacement kit provides four (4) extra SMP connectors used to repair broken connectors on the A9-CTC2, A9-DIMM5, and A9-CNTL test fixture products.

UDIMM Riser allow users to easily test and characterize DDR5 Unbuffered DIMM modules in a CTC2.

Versatile DIMM test card with focus on X16 receiver equalization and loopback BER testing.

Versatile DIMM test card with focus X8 on receiver equalization and loopback BER testing.

Software Libraries: https://github.com/AstekCorp/eGuardArduino.

Astek Corporation's High Speed Interconnect Tester (HSIT) enables high-speed testing of cables, slip-rings, backplanes and other interconnect technologies.

Astek Corporation's Interconnect Tester (QP-ICT) provides the ability to test one (1) to five (5) IEEE-1394b interconnects simultaneously. It is ideal for cable and interconnect/backplane testing.

Termination and Common Mode Load test fixture

QP-SIA and associated SSIB Controller provides facilities to test Data/Strobe signaling using an automated process.

QP-SIGKit-SSIB consists of the following components. Each component may also be purchased individually.

• Option -a -- consists of the following: QP-SSIB Control board, QP-SIA, QP-SSIB-TF-4, QP-SSIB-6-TF, QP-SMA24, QP-SMA26 and QP-DVM
• Option -b -- consists of the following: Everything in option -a plus QP-SSIB-9-TF and QP-SMA29

The A9-AUTO Reset Automation Kit is an upgrade kit for the Astek CTC2 test fixture and enables automated testing of DIMM and component test cards used on the CTC2.